Self-locking type steel nuts - Mechanical and functional requirements ISO 2320
Test clamping forces and torques for self-locking nut six edges class properties 04
| Thread dP | Test clamping force F80 and N | Test clamping force for assessing the overall friction factor | torque N.m | |||
|---|---|---|---|---|---|---|
| ceiling F75c N |
Lower limit F65d N | First bolting Tfv,max. e | The first release TFD, min. f | The fifth release TFD,min. f | ||
| M3 | 1 528 | 1 433 | 1 242 | 0,43 | 0,12 | 0,08 |
| M4 | 2 672 | 2 505 | 2 171 | 0,9 | 0,18 | 0,12 |
| M5 | 4 320 | 4 050 | 3 510 | 1,6 | 0,29 | 0,2 |
| M6 | 6 112 | 5 730 | 4 966 | 3 | 0,45 | 0,3 |
| M7 | 8 800 | 8 250 | 7 150 | 4,5 | 0,65 | 0,45 |
| M8 | 11 120 | 10 425 | 9 035 | 6 | 0,85 | 0,6 |
| M8x1 | 11 920 | 11 175 | 9 685 | 6 | 0,85 | 0,6 |
| M10 | 17 600 | 16 500 | 14 300 | 10,5 | 1,5 | 1 |
| M10x1,25 | 18 640 | 17 475 | 15 145 | 10,5 | 1,5 | 1 |
| M10x1 | 19 600 | 18 375 | 15 925 | 10,5 | 1,5 | 1 |
| M12 | 25 600 | 24 000 | 20 800 | 15,5 | 2,3 | 1,6 |
| M12x1,5 | 26 800 | 25 125 | 21 775 | 15,5 | 2,3 | 1,6 |
| M12x1,25 | 28 000 | 26 250 | 22 750 | 15,5 | 2,3 | 1,6 |
| M14 | 34 960 | 32 775 | 28 405 | 24 | 3,3 | 2,3 |
| M14x1,5 | 38 000 | 35 625 | 30 875 | 24 | 3,3 | 2,3 |
| M16 | 47 760 | 44 775 | 38 805 | 32 | 4,5 | 3 |
| M16x1,5 | 50 800 | 47 625 | 41 275 | 32 | 4,5 | 3 |
| M18 | 58 400 | 54 750 | 47 450 | 42 | 6 | 4,2 |
| M18x1,5 | 65 360 | 61 275 | 53 105 | 42 | 6 | 4,2 |
| M20 | 74 480 | 69 825 | 60 515 | 54 | 7,5 | 5,3 |
| M20x1,5 | 82 720 | 77 550 | 67 210 | 54 | 7,5 | 5,3 |
| M22 | 92 080 | 86 325 | 74 815 | 68 | 9,5 | 6,5 |
| M22x1,5 | 101 200 | 94 875 | 82 225 | 68 | 9,5 | 6,5 |
| M24 | 107 280 | 100 575 | 87 165 | 80 | 11,5 | 8 |
| M24x2 | 116 720 | 109 425 | 94 835 | 80 | 11,5 | 8 |
| M27 | 139 520 | 130 800 | 113 360 | 94 | 13,5 | 10 |
| M27x2 | 150 800 | 141 375 | 122 525 | 94 | 13,5 | 10 |
| M30 | 170 560 | 159 900 | 138 580 | 108 | 16 | 12 |
| M30x2 | 188 800 | 177 000 | 153 400 | 108 | 16 | 12 |
| M33 | 210 960 | 197 775 | 171 405 | 122 | 18 | 14 |
| M33x2 | 231 360 | 216 900 | 187 980 | 122 | 18 | 14 |
| M36 | 248 400 | 232 875 | 201 825 | 136 | 21 | 16 |
| M36x3 | 262 960 | 246 525 | 213 655 | 136 | 21 | 16 |
| M39 | 296 720 | 278 175 | 241 085 | 150 | 23 | 18 |
| M39x3 | 313 120 | 293 550 | 254 410 | 150 | 23 | 18 |
NOTE Calculation results of the test self-locking torque statistical control methods pnooesu (SPC) has no statistical significance
a Clamping force nuts for strength class 04 is equal to 80% of the test load for nuts strength class 04 nominal diameter of 3 mm
b see Annex B.
c The upper limit of the clamping force is equal to 75% of the test load, see Annex B.
d The lower limit of clamping force is equal to 65% of the test load, see Annex B.
e Torque for the first installation of a self-metal self-locking hex nuts. Torque for the self-locking hexagon nuts with non-metallic liner must be a maximum of 50% of the value.
f The values in this table are required to perform tests in accordance with the test conditions in the laboratory. Using this type of fasteners is dependent upon the delivery and execution may vary in normal use. It is recommended that further testing requirements pn complete connections using serial parts were placed on functionality, if functionality is required.
Test clamping forces and torques for self-locking hex nut class properties05
| Thread dP | Test clamping force F80 a N | Test clamping force for assessing the overall friction factor | torque N.m | |||
|---|---|---|---|---|---|---|
| ceiling F75c N |
Lower limit F65d N | first bolting Tfv,max. e | first release TFd,min. f | The fifth releaseTFd,min. f | ||
| M3 | 2 000 | 1 875 | 1 625 | 0,6 | 0,15 | 0,1 |
| M4 | 3 520 | 3 300 | 2 860 | 1,2 | 0,22 | 0,15 |
| M5 | 5 680 | 5 325 | 4 615 | 2,1 | 0,35 | 0,24 |
| M6 | 8 000 | 7 500 | 6 500 | 4 | 0,55 | 0,4 |
| M7 | 11 600 | 10 875 | 9 425 | 6 | 0,85 | 0,6 |
| M8 | 14 640 | 13 725 | 11 895 | 8 | 1,15 | 0,8 |
| M8x1 | 15 680 | 14 700 | 12 740 | 8 | 1,15 | 0,8 |
| M10 | 23 200 | 21 750 | 18 850 | 14 | 2 | 1,4 |
| M10x1,25 | 24 480 | 22 950 | 19 890 | 14 | 2 | 1,4 |
| M10x1 | 25 760 | 24 150 | 20 930 | 14 | 2 | 1,4 |
| M12 | 33 760 | 31 650 | 27 430 | 21 | 3,1 | 2,1 |
| M12x1,5 | 35 200 | 33 000 | 28 600 | 21 | 3,1 | 2,1 |
| M12x1,25 | 36 800 | 34 500 | 29 900 | 21 | 3,1 | 2,1 |
| M14 | 46 000 | 43 125 | 37 375 | 31 | 4,4 | 3 |
| M14x1,5 | 50 000 | 46 875 | 40 625 | 31 | 4,4 | 3 |
| M16 | 62 800 | 58 875 | 51 025 | 42 | 6 | 4.2 |
| M16x1,5 | 66 800 | 62 625 | 54 275 | 42 | 6 | 4,2 |
| M18 | 76 800 | 72 000 | 62 400 | 56 | 8 | 5,5 |
| M18x1,5 | 86 000 | 80 625 | 69 875 | 56 | 8 | 5,5 |
| M20 | 98 000 | 91 875 | 79 625 | 72 | 10,5 | 7 |
| M20x1,5 | 108 800 | 102 000 | 88 400 | 72 | 10,5 | 7 |
| M22 | 121 200 | 113 625 | 98 475 | 90 | 13 | 9 |
| M22x1,5 | 133 200 | 124 875 | 108 225 | 90 | 13 | 9 |
| M24 | 141 200 | 132 375 | 114 725 | 106 | 15 | 10,5 |
| M24x2 | 153 600 | 144 000 | 124 800 | 106 | 15 | 10,5 |
| M27 | 183 600 | 172 125 | 149 175 | 123 | 17 | 12 |
| M27x2 | 198 400 | 186 000 | 161 200 | 123 | 17 | 12 |
| M30 | 224 400 | 210 375 | 182 325 | 140 | 19 | 14 |
| M30x2 | 248 400 | 232 875 | 201 825 | 140 | 19 | 14 |
| M33 | 277 600 | 260 250 | 225 550 | 160 | 21,5 | 15,5 |
| M33x2 | 304 400 | 285 375 | 247 325 | 160 | 21,5 | 15,5 |
| M36 | 326 800 | 306 375 | 265 525 | 180 | 24 | 17,5 |
| M36x3 | 346 000 | 324 375 | 281 125 | 180 | 24 | 17,5 |
| M39 | 390 400 | 366 000 | 317 200 | 200 | 26,5 | 19,5 |
| M39x3 | 412 000 | 386 250 | 334 750 | 200 | 26,5 | |
NOTE Calculation results of the test self-locking torque statistical control methods pnooesu (SPC) has no statistical significance
a Clamping force nuts for strength class 04 is equal to 80% of the test load for nuts strength class 04 nominal diameter of 3 mm
b See Annex B.
c Value of upper limit clamping force is equal to 75% of the test load, see Appendix B.
d The lower limit of clamping force is equal to 65% of the test load, see Appendix B.
e Torque for the first installation only all-metal self-locking hex nuts. Torque for the self-locking hexagon nuts with non-metallic liner must be a maximum of 50% of the value.
f The values in this table are required to perform tests in accordance with the test conditions in the laboratory. Using this type of fasteners is dependent upon the delivery and execution may vary in normal use. It is recommended that further testing requirements pn complete connections using serial parts were placed on functionality, if functionality is required.
Test clamping forces and torques for self-locking hex nut class properties 5
| Thread dP | Test clamping forceF80 a N | Test clamping force for assessing the overall friction factor | torque N.m | |||
|---|---|---|---|---|---|---|
| ceiling F75c N |
Lower limit F65d N | First bolting Tfv,max. e | First releaseTFd,min. f | The fifth releaseTFd,min. f | ||
| M3 | 1 528 | 1 433 | 1 242 | 0,43 | 0,12 | 0,08 |
| M4 | 2 672 | 2 505 | 2 171 | 0,9 | 0.18 | 0,12 |
| M5 | 4 320 | 4 050 | 3 510 | 1,6 | 0.29 | 0,2 |
| M6 | 6 112 | 5 730 | 4 966 | 3 | 0,45 | 0,3 |
| M7 | 8 800 | 8 250 | 7 150 | 4,5 | 0,65 | 0,45 |
| M8 | 11 120 | 10 425 | 9 035 | 6 | 0,85 | 0,6 |
| M8x1 | 11 920 | 11 175 | 9 685 | 6 | 0,85 | 0,6 |
| M10 | 17 600 | 16 500 | 14 300 | 10,5 | 1,5 | 1 |
| M10x1,25 | 18 640 | 17 475 | 15 145 | 10,5 | 1,5 | 1 |
| M10x1 | 19 600 | 18 375 | 15 925 | 10,5 | 1,5 | 1 |
| M12 | 25 600 | 24 000 | 20 800 | 15,5 | 2,3 | 1,6 |
| M12x1,5 | 26 800 | 25 125 | 21 775 | 15,5 | 2,3 | 1,6 |
| M12x1,25 | 28 000 | 26 250 | 22 750 | 15,5 | 2,3 | 1,6 |
| M14 | 34 960 | 32 775 | 28 405 | 24 | 3,3 | 2,3 |
| M14x1,5 | 38 000 | 35 625 | 30 875 | 24 | 3,3 | 2,3 |
| M16 | 47 760 | 44 775 | 38 805 | 32 | 4,5 | 3 |
| M16x1,5 | 50 800 | 47 625 | 41 275 | 32 | 4,5 | 3 |
| M18 | 58 400 | 54 750 | 47 450 | 42 | 6 | 4,2 |
| M18x1,5 | 65 680 | 61 575 | 53 365 | 42 | 6 | 4,2 |
| M20 | 74 480 | 69 825 | 60 515 | 54 | 7,5 | 5,3 |
| M20x1,5 | 82 400 | 77 250 | 66 950 | 54 | 7,5 | 5,3 |
| M22 | 92 000 | 86 250 | 74 750 | 68 | 9,5 | 6,5 |
| M22x1,5 | 100 800 | 94 500 | 81 900 | 68 | 9,5 | 6,5 |
| M24 | 107 200 | 100 500 | 87 100 | 80 | 11,5 | 8 |
| M24x2 | 116 800 | 109 500 | 94 900 | 80 | 11,5 | 8 |
| M27 | 113 600 | 106 500 | 92 300 | 94 | 13,5 | 10 |
| M27x2 | 123 200 | 115 500 | 100 100 | 94 | 13,5 | 10 |
| M30 | 139 200 | 130 500 | 113 100 | 108 | 16 | 12 |
| M30x2 | 153 600 | 144 000 | 124 800 | 108 | 16 | 12 |
| M33 | 172 000 | 161 250 | 139 750 | 122 | 18 | 14 |
| M33x2 | 188 800 | 177 000 | 153 400 | 122 | 18 | 14 |
| M36 | 202 400 | 189 750 | 164 450 | 136 | 21 | 16 |
| M36x3 | 214 400 | 201 000 | 174 200 | 136 | 21 | 16 |
| M39 | 242 400 | 227 250 | 196 950 | 150 | 23 | 18 |
| M39x3 | 255 200 | 239 250 | 207 350 | 150 | 23 | |
PNote Calculation results of the test self-locking torque statistical control methods pnooesu (SPC) has no statistical significance
a Clamping force nuts for strength class 04 is equal to 80% of the test load for nuts strength class 04 nominal diameter of 3 mm
b Viz p酶铆loha B.
c Value of upper limit clamping force is equal to 75% of the test load, see Annex B.
d The lower limit of clamping force is equal to 65% of the test load, see Appendix B.
e Torque for the first installation only all-metal self-locking hex nuts. Torque for the self-locking hexagon nuts with non-metallic liner must be a maximum of 50% of the value.
f The values in this table are required to perform tests in accordance with the test conditions in the laboratory. Using this type of fasteners is dependent upon the delivery and execution may vary in normal use. It is recommended that additional testing requirements complete pn joint use of serial parts were placed on functionality, if functionality is required.
Test clamping forces and torques for self-locking hex nut class properties 6
| Thread dP | Test clamping forceF80 a N | Test clamping force for assessing the overall friction factor | torque N.m | |||
|---|---|---|---|---|---|---|
| ceiling F75c N |
Lower limit F65d N | First bolting Tfv,max. e | First releaseTFd,min. f | The fifth releaseTFd,min. f | ||
| M3 | 1 768 | 1 658 | 1 437 | 0,43 | 0,12 | 0,08 |
| M4 | 3 088 | 2 895 | 2 509 | 0,9 | 0.18 | 0,12 |
| M5 | 5 000 | 4 688 | 4 063 | 1,6 | 0,29 | 0,2 |
| M6 | 7 072 | 6 630 | 5 746 | 3 | 0,45 | 0,3 |
| M7 | 10 160 | 9 525 | 8 255 | 4,5 | 0,65 | 0,45 |
| M8 | 12 880 | 12 075 | 10 465 | 6 | 0,85 | 0,6 |
| M8x1 | 13 760 | 12 900 | 11 180 | 6 | 0,85 | 0,6 |
| M10 | 20 400 | 19 125 | 16 575 | 10,5 | 1,5 | 1 |
| M10x1,25 | 21 520 | 20 175 | 17 485 | 10,5 | 1,5 | 1 |
| M10x1 | 22 720 | 21 300 | 18 460 | 10,5 | 1,5 | 1 |
| M12 | 29 680 | 27 825 | 24 115 | 15,5 | 2,3 | 1,6 |
| M12x1,5 | 31 040 | 29 100 | 25 220 | 15,5 | 2,3 | 1,6 |
| M12x1,25 | 32 400 | 30 375 | 26 325 | 15,5 | 2,3 | 1,6 |
| M14 | 40 480 | 37 950 | 32 890 | 24 | 3,3 | 2,3 |
| M14x1,5 | 44 000 | 41 250 | 35 750 | 24 | 3,3 | 2,3 |
| M16 | 55 280 | 51 825 | 44 915 | 32 | 4,5 | 3 |
| M16x1,5 | 58 800 | 55 125 | 47 775 | 32 | 4,5 | 3 |
| M18 | 67 600 | 63 375 | 54 925 | 42 | 6 | 4,2 |
| M18x1,5 | 76 000 | 71 250 | 61 750 | 42 | 6 | 4,2 |
| M20 | 86 400 | 81 000 | 70 200 | 54 | 7,5 | 5,3 |
| M20x1,5 | 96 000 | 90 000 | 78 000 | 54 | 7,5 | 5,3 |
| M22 | 106 400 | 99 750 | 86 450 | 68 | 9,5 | 6,5 |
| M22x1,5 | 116 800 | 109 500 | 94 900 | 68 | 9,5 | 6,5 |
| M24 | 124 000 | 116 250 | 100 750 | 80 | 11,5 | 8 |
| M24x2 | 135 200 | 126 750 | 109 850 | 80 | 11,5 | 8 |
| M27 | 161 600 | 151 500 | 131 300 | 94 | 13,5 | 10 |
| M27x2 | 174 400 | 163 500 | 141 700 | 94 | 13,5 | 10 |
| M30 | 197 600 | 185 250 | 160 550 | 108 | 16 | 12 |
| M30x2 | 218 400 | 204 750 | 177 450 | 108 | 16 | 12 |
| M33 | 244 000 | 228 750 | 198 250 | 122 | 18 | 14 |
| M33x2 | 268 000 | 251 250 | 217 750 | 122 | 18 | 14 |
| M36 | 287 200 | 269 250 | 233 350 | 136 | 21 | 16 |
| M36x3 | 304 800 | 285 750 | 247 650 | 136 | 21 | 16 |
| M39 | 343 200 | 321 750 | 278 850 | 150 | 23 | 18 |
| M39x3 | 362 400 | 339 750 | 294 450 | 150 | 23 | |
a Clamping force nuts for strength class 04 is equal to 80% of the test load for nuts strength class 04 nominal diameter of 3 mm
b See appendix B.
c Value of upper limit clamping force is equal to 75% of the test load, see Appendix B.
d to calculate the lower clamping force is equal to 65% of the test load, see Appendix B.
e Torque for the first installation only samojistn媒ch all-metal hexagon nuts. Torque for the self-locking hex matrix with non-metallic liner must be a maximum of 50% of the value.
f The values in this table are required to perform tests in accordance with the test conditions in the laboratory. Using this type of fasteners is dependent upon the delivery and execution may vary in normal use. It is recommended that further testing requirements pn complete connections using serial parts were placed on functionality, if functionality is required.
Test clamping forces and torques for self-locking hex nut characteristics of Class 8
| Thread dP | Test clamping forceF80 a N | Test clamping force for assessing the overall friction factor | torque N.m | |||
|---|---|---|---|---|---|---|
| ceiling F75c N |
Lower limit F65d N | First bolting Tfv,max. e | First releaseTFd,min. f | The fifth releaseTFd,min. f | ||
| M3 | 2 336 | 2 190 | 1 898 | 0,43 | 0,12 | 0,08 |
| M4 | 4 080 | 3 825 | 3 315 | 0,9 | 0,18 | 0,12 |
| M5 | 6 584 | 6 173 | 5 350 | 1,6 | 0,29 | 0,2 |
| M6 | 9 280 | 8 700 | 7 540 | 3 | 0,45 | 0,3 |
| M7 | 13 440 | 12 600 | 10 920 | 4,5 | 0,65 | 0,45 |
| M8 | 16 960 | 15 900 | 13 780 | 6 | 0,85 | 0,6 |
| M8x1 | 18 160 | 17 025 | 14 755 | 6 | 0,85 | 0,6 |
| M10 | 26 960 | 25 275 | 21 905 | 10,5 | 1,5 | 1 |
| M10x1,25 | 28 400 | 26 625 | 23 075 | 10,5 | 1,5 | 1 |
| M10x1 | 29 920 | 28 050 | 24 310 | 10,5 | 1,5 | 1 |
| M12 | 39 120 | 36 675 | 31 785 | 15,5 | 2,3 | 1,6 |
| M12x1,5 | 40 880 | 38 325 | 33 215 | 15,5 | 2,3 | 1,6 |
| M12x1,25 | 42 720 | 40 050 | 34 710 | 15,5 | 2,3 | 1,6 |
| M14 | 53 360 | 50 025 | 43 355 | 24 | 3,3 | 2,3 |
| M14x1,5 | 58 000 | 54 375 | 47 125 | 24 | 3,3 | 2,3 |
| M16 | 72 800 | 68 250 | 59 150 | 32 | 4,5 | 3 |
| M16x1,5 | 77 520 | 72 675 | 62 985 | 32 | 4,5 | 3 |
| M18 | 92 000 | 86 250 | 74 750 | 42 | 6 | 4,2 |
| M18x1,5 | 104 000 | 97 500 | 84 500 | 42 | 6 | 4,2 |
| M20 | 117 600 | 110 250 | 95 550 | 54 | 7,5 | 5,3 |
| M20x1,5 | 130 400 | 122 250 | 105 950 | 54 | 7,5 | 5,3 |
| M22 | 145 600 | 136 500 | 118 300 | 68 | 9,5 | 6,5 |
| M22x1,5 | 160 000 | 150 000 | 130 000 | 68 | 9,5 | 6,5 |
| M24 | 169 600 | 159 000 | 137 800 | 80 | 11,5 | 8 |
| M24x2 | 184 000 | 172 500 | 149 500 | 80 | 11,5 | 8 |
| M27 | 220 000 | 206 250 | 178 750 | 94 | 13,5 | 10 |
| M27x2 | 238 400 | 223 500 | 193 700 | 94 | 13,5 | 10 |
| M30 | 269 600 | 252 750 | 219 050 | 108 | 16 | 12 |
| M30x2 | 298 400 | 279 750 | 242 450 | 108 | 16 | 12 |
| M33 | 332 800 | 312 000 | 270 400 | 122 | 18 | 14 |
| M33x2 | 365 600 | 342 750 | 297 050 | 122 | 18 | 14 |
| M36 | 392 000 | 367 500 | 318 500 | 136 | 21 | 16 |
| M36x3 | 415 200 | 389 250 | 337 350 | 136 | 21 | 16 |
| M39 | 468 800 | 439 500 | 380 900 | 150 | 23 | 18 |
| M39x3 | 494 400 | 463 500 | 401 700 | 150 | 23 | |
a Clamping force nuts for strength class 04 is equal to 80% of the test load for nuts strength class 04 nominal diameter of 3 mm
b Viz p酶铆loha B.
c Value of upper limit clamping force is equal to 75% of the test load, see Appendix B.
d to calculate the lower clamping force is equal to 65% of the test load, see Appendix B.
e Torque for the first installation only samojistn媒ch all-metal hexagon nuts. Torque for the self-locking hex matrix with non-metallic liner must be a maximum of 50% of the value.
f The values in this table are required to perform tests in accordance with the test conditions in the laboratory. Using this type of fasteners is dependent upon the delivery and execution may vary in normal use. It is recommended that further testing requirements pn complete connections using serial parts were placed on functionality, if functionality is required.
Test clamping forces and torques for self-locking hex nut characteristics of Class 9
| Thread dP | Test clamping forceF80 a N | Test clamping force for assessing the overall friction factor | torque N.m | |||
|---|---|---|---|---|---|---|
| ceiling F75c N |
Lower limit F65d N | First bolting Tfv,max. e | First releaseTFd,min. f | The fifth releaseTFd,min. f | ||
| M3 | 2 616 | 2 453 | 2 126 | 0,43 | 0,12 | 0,08 |
| M4 | 4 568 | 4 283 | 3712 | 0,9 | 0,18 | 0,12 |
| M5 | 7 384 | 6 923 | 6 000 | 1,6 | 0,29 | 0,2 |
| M6 | 10 480 | 9 825 | 8 515 | 3 | 0,45 | 0,3 |
| M7 | 15 040 | 14 100 | 12 220 | 4,5 | 0,65 | 0,45 |
| M8 | 19 040 | 17 850 | 15 470 | 6 | 0,85 | 0,6 |
| M8x1 | 20 400 | 19 125 | 16 575 | 6 | 0,85 | 0,6 |
| M10 | 30 160 | 28 275 | 24 505 | 10,5 | 1,5 | 1 |
| M10x1,25 | 31 840 | 29 850 | 25 870 | 10,5 | 1,5 | 1 |
| M10x1 | 33 520 | 31 425 | 27 235 | 10,5 | 1,5 | 1 |
| M12 | 43 840 | 41 100 | 35 620 | 15,5 | 2,3 | 1,6 |
| M12x1,5 | 45 840 | 42 975 | 37 245 | 15,5 | 2,3 | 1,6 |
| M12x1,25 | 47 920 | 44 925 | 38 935 | 15,5 | 2,3 | 1,6 |
| M14 | 59 840 | 56 100 | 48 620 | 24 | 3,3 | 2,3 |
| M14x1,5 | 64 960 | 60 900 | 52 780 | 24 | 3,3 | 2,3 |
| M16 | 81 600 | 76 500 | 66 300 | 32 | 4,5 | 3 |
| M16x1,5 | 87 200 | 81 750 | 70 850 | 32 | 4,5 | |
a Clamping force nuts for strength class 04 is equal to 80% of the test load for nuts strength class 04 nominal diameter of 3 mm
b Viz p酶铆loha B.
c Value of upper limit clamping force is equal to 75% of the test load, see Appendix B.
d to calculate the lower clamping force is equal to 65% of the test load, see Appendix B.
e Torque for the first installation only samojistn媒ch all-metal hexagon nuts. Torque for the self-locking hex matrix with non-metallic liner must be a maximum of 50% of the value.
f The values in this table are required to perform tests in accordance with the test conditions in the laboratory. Using this type of fasteners is dependent upon the delivery and execution may vary in normal use. It is recommended that further testing requirements pn complete connections using serial parts were placed on functionality, if functionality is required.
Test clamping forces and torques for self-locking hex nut characteristics of Class 10
| Thread dP | Test clamping forceF80 a N | Test clamping force for assessing the overall friction factor | torque N.m | |||
|---|---|---|---|---|---|---|
| ceiling F75c N |
Lower limit F65d N | First bolting Tfv,max. e | First releaseTFd,min. f | The fifth releaseTFd,min. f | ||
| M3 | 3 344 | 3 135 | 2 717 | 0,6 | 0,15 | 0,1 |
| M4 | 5 832 | 5 468 | 4 739 | 1,2 | 0,22 | 0,15 |
| M5 | 9 440 | 8 850 | 7 670 | 2,1 | 0,35 | 0,24 |
| M6 | 13 360 | 12 525 | 10 855 | 4 | 0,55 | 0,4 |
| M7 | 19 200 | 18 000 | 15 600 | 6 | 0,85 | 0,6 |
| M8 | 24 320 | 22 800 | 19 760 | 8 | 1,15 | 0,8 |
| M8x1 | 26 000 | 24 375 | 21 125 | 8 | 1,15 | 0,8 |
| M10 | 38 480 | 36 075 | 31 265 | 14 | 2 | 1,4 |
| M10x1,25 | 40 640 | 38 100 | 33 020 | 14 | 2 | 1,4 |
| M10x1 | 42 800 | 40 125 | 34 775 | 14 | 2 | 1,4 |
| M12 | 56 000 | 52 500 | 45 500 | 21 | 3,1 | 2,1 |
| M12x1,5 | 58 480 | 54 825 | 47 515 | 21 | 3,1 | 2,1 |
| M12x1,25 | 61 120 | 57 300 | 49 660 | 21 | 3,1 | 2,1 |
| M14 | 76 400 | 71 625 | 62 075 | 31 | 4,4 | 3 |
| M14x1,5 | 83 200 | 78 000 | 67 600 | 31 | 4,4 | 3 |
| M16 | 104 000 | 97 500 | 84 500 | 42 | 6 | 4,2 |
| M16x1,5 | 111 200 | 104 250 | 90 350 | 42 | 6 | 4,2 |
| M18 | 127 200 | 119 250 | 103 350 | 56 | 8 | 5,5 |
| M18x1,5 | 143 200 | 134 250 | 116 350 | 56 | 8 | 5,5 |
| M20 | 162 400 | 152 250 | 131 950 | 72 | 10,5 | 7 |
| M20x1,5 | 180 800 | 169 500 | 146 900 | 72 | 10,5 | 7 |
| M22 | 201 600 | 189 000 | 163 800 | 90 | 13 | 9 |
| M22x1,5 | 220 800 | 207 000 | 179 400 | 90 | 13 | 9 |
| M24 | 234 400 | 219 750 | 190 450 | 106 | 15 | 10,5 |
| M24x2 | 255 200 | 239 250 | 207 350 | 106 | 15 | 10,5 |
| M27 | 304 800 | 285 750 | 247 650 | 123 | 17 | 12 |
| M27x2 | 329 600 | 309 000 | 267 800 | 123 | 17 | 12 |
| M30 | 372 800 | 349 500 | 302 900 | 140 | 19 | 14 |
| M30x2 | 412 000 | 386 250 | 334 750 | 140 | 19 | 14 |
| M33 | 460 800 | 432 000 | 374 400 | 160 | 21,5 | 15,5 |
| M33x2 | 505 600 | 474 000 | 410 800 | 160 | 21,5 | 15,5 |
| M36 | 542 400 | 508 500 | 440 700 | 180 | 24 | 17,5 |
| M36x3 | 574 400 | 538 500 | 466 700 | 180 | 24 | 17,5 |
| M39 | 648 000 | 607 500 | 526 500 | 200 | 26,5 | 19,5 |
| M39x3 | 684 000 | 641 250 | 555 750 | 200 | 26,5 | |
aClamping force nuts for strength class 04 is equal to 80% of the test load for nuts strength class 04 nominal diameter of 3 mm
b Viz p酶铆loha B.
c Value of upper limit clamping force is equal to 75% of the test load, see Appendix B.
d to calculate the lower clamping force is equal to 65% of the test load, see Appendix B.
e Torque for the first installation only samojistn媒ch all-metal hexagon nuts. Torque for the self-locking hex matrix with non-metallic liner must be a maximum of 50% of the value.
f The values in this table are required to perform tests in accordance with the test conditions in the laboratory. Using this type of fasteners is dependent upon the delivery and execution may vary in normal use. It is recommended that further testing requirements pn complete connections using serial parts were placed on functionality, if functionality is required.
Test clamping forces and torques for self-locking hex nut characteristics of Class 12
| Thread dP | Test clamping forceF80 a N | Test clamping force for assessing the overall friction factor | torque N.m | |||
|---|---|---|---|---|---|---|
| ceiling F75c N |
Lower limit F65d N | First bolting Tfv,max. e | First releaseTFd,min. f | The fifth releaseTFd,min. f | ||
| M3 | 3 904 | 3 660 | 3 172 | 0,6 | 0.15 | 0,1 |
| M4 | 6 816 | 6 390 | 5 538 | 1,2 | 0,22 | 0,15 |
| M5 | 11 040 | 10 350 | 8 970 | 2,1 | 0,35 | 0,24 |
| M6 | 15 600 | 14 625 | 12 675 | 4 | 0,55 | 0,4 |
| M7 | 22 400 | 21 000 | 18 200 | 6 | 0,85 | 0,6 |
| M8 | 28 400 | 26 625 | 23 075 | 8 | 1,15 | 0,8 |
| M8x1 | 30 400 | 28 500 | 24 700 | 8 | 1,15 | 0,8 |
| M10 | 45 040 | 42 225 | 36 595 | 14 | 2 | 1,4 |
| M10x1,25 | 47 520 | 44 550 | 38 610 | 14 | 2 | 1,4 |
| M10x1 | 50 160 | 47 025 | 40 755 | 14 | 2 | 1,5 |
| M12 | 65 440 | 61 350 | 53 170 | 21 | 3,1 | 2,1 |
| M12x1,5 | 68 400 | 64 125 | 55 575 | 21 | 3,1 | 2,1 |
| M12x1,25 | 71 440 | 66 975 | 58 045 | 21 | 3,1 | 2,1 |
| M14 | 89 600 | 84 000 | 72 800 | 31 | 4,4 | 3 |
| M14x1,5 | 96 800 | 90 750 | 78 650 | 31 | 4,4 | 3 |
| M16 | 121 600 | 114 000 | 98 800 | 42 | 6 | 4,2 |
| M16x1,5 | 129 600 | 121 500 | 105 300 | 42 | 6 | 4,2 |
| M18 | 148 800 | 139 500 | 120 900 | 56 | 8 | 5,5 |
| M18x1,5 | 168 000 | 157 500 | 136 500 | 56 | 8 | 5,5 |
| M20 | 190 400 | 178 500 | 154 700 | 72 | 10,5 | 7 |
| M20x1,5 | 211 200 | 198 000 | 171 600 | 72 | 10,5 | 7 |
| M22 | 235 200 | 220 500 | 191 100 | 90 | 13 | 9 |
| M22x1,5 | 258 400 | 242 250 | 209 950 | 90 | 13 | 9 |
| M24 | 273 600 | 256 500 | 222 300 | 106 | 15 | 10,5 |
| M24x2 | 297 600 | 279 000 | 241 800 | 106 | 15 | 10,5 |
| M27 | 356 000 | 333 750 | 289 250 | 123 | 17 | 12 |
| M27x2 | 384 800 | 360 750 | 312 650 | 123 | 17 | 12 |
| M30 | 435 200 | 408 000 | 353 600 | 140 | 19 | 14 |
| M30x2 | 481 600 | 451 500 | 391 300 | 140 | 19 | 14 |
| M33 | 538 400 | 504 750 | 374 400 | 160 | 21,5 | 15,5 |
| M33x2 | 590 400 | 553 500 | 479 700 | 160 | 21,5 | 15,5 |
| M36 | 633 600 | 594 000 | 514 800 | 180 | 24 | 17,5 |
| M36x3 | 671 200 | 629 250 | 545 350 | 180 | 24 | 17,5 |
| M39 | 757 600 | 710 250 | 615 550 | 200 | 26,5 | 19,5 |
| M39x3 | 799 200 | 749 250 | 649 350 | 200 | 26,5 | |
a Clamping force nuts for strength class 04 is equal to 80% of the test load for nuts strength class 04 nominal diameter of 3 mm
b Viz p酶铆loha B.
c Value of upper limit clamping force is equal to 75% of the test load, see Appendix B.
d to calculate the lower clamping force is equal to 65% of the test load, see Appendix B.
e Torque for the first installation only samojistn媒ch all-metal hexagon nuts. Torque for the self-locking hex matrix with non-metallic liner must be a maximum of 50% of the value.
f The values in this table are required to perform tests in accordance with the test conditions in the laboratory. Using this type of fasteners is dependent upon the delivery and execution may vary in normal use. It is recommended that further testing requirements pn complete connections using serial parts were placed on functionality, if functionality is required.